TB6600 Stepper Motor Driver Controller 0.2-5A CNC Router HY-DIV268N-5A 12-48V for Engraving Machine Tools
Average current control, two-phase sinusoidal current output.
DC 12~48V power supply, the internal integration of 12V and 5V regulator.
Optically isolated signal input/output
Protection against overvoltage, undervoltage, overcurrent and short circuit white
The input current from 1 to 5 amps, select the drive to stepper motor.
Output current 0.2A ~ 5A
Operating temperature -10 to 45 °C; Storage temperature -40°C to 70°C.
Moisture without condensation, no sagging
Forbidden gas combustible gas and conductive dust
Weight 200 grams
Two-phase hybrid stepper motor dynamic voltage 12 to 48V, current is less than 5A outer diameter 35 to 86mm.�
This driver uses drive current loop subdivision control, motor torque ripple is very small, low speed operation is very smooth, almost no vibration and noise.High-speed torque is much higher than other two-phase motors, high positioning accuracy. Widely used in engraving machine, CNC machine tools, packaging machinery and other high-resolution requirements on the device.
High speed optoelectronic isolation signal input
Single-chip PWM bipolar sinusoidal chopper ensures low vibration and high efficiency
1, 2, 4 (New Mode), 8, 16 adjustable microstep control, motors run more precisely and smoothly
TB6600 Stepper Motor Driver Controller 0.2-5A CNC Router HY-DIV268N-5A 12-48V for Engraving Machine Tools
Control signal interface
PUL : step pulse signal is the input side or positive pulse signal input terminal
PUL-: The negative input of the negative input pulse signal or a positive pulse signal.
DIR : Step direction signal input to positive terminal or negative pulse signal input to positive terminal.
DIR -: negative side step direction signal input or negative terminal reverse step pulse signal input
IN : offline can reset the input side of the signal is
IN-: no connection can reset the signal input negative terminal
Offline trigger signal is active, reset the drive fault to avoid any pulse, the drive output
The power component is off, the motor maintains torque.
Control of signal connections
PC control signal can be high, can also be effective low. When active high, the control signal
The negative side together as a low trigger signal, positive side of all control signals together as a common signal.
For example, the PNP and open collector output interface circuit diagram is as follows:
NOTE: VCC is 5V, R short
VCC value of 12V, R 1K, resistance of more than 1/8W;
VCC value of 24V, R 2K, resistance of more than 1/8W;
Adjust the revolution stepper motor
The unit for setting the number of steps per motor revolution is 200 (full step), 400 (2 segments), 1600 (8 segments), 3200 steps (16 segments).
The user can drive the front panel DIP switch SW3 is SW4 drive bit to set the number of steps (such as table 1)
The power interface
DC : DC power level, DC power supply voltage 12 to 48V. The maximum current is 5A. The
DC-: DC power supply negative level.
A AB B-: to connect the two-phase hybrid stepper motor
Two-phase hybrid stepper motor connection with the four-wire system, the motor windings in parallel and series connection, and connection method, high-speed performance,. But the drive current is large (for the motor winding current of 1.73 times), connected in series when the drive current is equal to the motor winding current.
Overload, over current, overheat, over voltage and under voltage protection to avoid damaging your computer and devices.
Cooling Aluminium Box Design for Cooling, and protect the driver board from being damaged by dirt, dust or other liquids.
Moreover, the brand new design with BiCD0.13 (50V) process technology on the chipset also ensures maximum 5.0A output current and 50V output withstand voltage.
